CONSTRUCTION OF CAR TOUCH INTRUDER ALARM
Sold By: Joe Project Store | Item Type: Project Material | Report this? | Attributes: 65 pages | 1-5 chapters | Amount: ₦5,000 | 2 orders. | Marked useful: 8,299 times
INSTANT PROJECT MATERIAL DOWNLOADABSTRACT
The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuitthereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer.
This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.
TABLE OF CONTENT
CHAPTER ONE: Introduction 1.1 Background of study
1.2 Aims and objectives
CHAPTER TWO: Literature Review
CHAPTER THREE: Specification and operation of system component 3.1 Description of NE55 Timer
3.2 Description of Resistor
3.3 Description of Capacitor
3.4 Description of Diode
3.5 Description of Transformer
3.6 Description of Loud Speaker and Buzzer
3.7 Description of Transistor
3. 8 Description of L.E.D
CHAPTER FOUR: Operation of system and its circuit and block diagram
4.1 Operation of
4.2 The circuit diagram
4.3 The block diagram
CHAPTER FIVE: Construction, Testing and Packaging
5.1 Values of components
5.2 Assembly
5.3 A schematic diagram of the finished work
CHAPTER SIX: Conclusion and Recommendation
6.1 Conclusion
6.2 Recommendation
6.3 Observations
6.4 Dificulties
6.5 Reference
LIST OF SYMBOLS
NAME SYMBOLS
Resistor
TransistorDiode
Zener diode
Trimmer capacitor
Polarized capacitor
Unpolarized capacitor
Variable capacitor
CHAPTER ONE: INTRODUCTION
1.1. Background of the Study
The first car alarm was a primitive contraption that utilized a bell or horn connected to the drive shaft. It was created by an unnamed Nebraska inventor in June 20th, 1920. It utilizes the drive shaft to operate its own bell or horn signal when the car is properly moved. This is just a little talk on a car alarm but not a car touch intruder alarm which is a modern, more advanced, and more reliable type of car alarm.
This car touch sensitive alarm project consist of three NE555 timer IC, the first NE555 was wired as monostable multi-vibrator and the remaining two were wired as tone generator. When the sensor is touch or has contact with human hand perhaps body, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of R4 (10M) and Q1 (transistor) was bias via R3 and this transistor is in such a way that once it was biased it will supply a negative voltage to tone generator thereby making two NE555 timer which was know as (tone generator) to oscillate to make a bell sound through the buzzer. The tone generators are configured as an astable multi-vibrator whose oscillation frequency can be varied with the help of PR1 and PR2. By adjusting the values of PR1 and PR2, modifications on the tone are possible.
The reset button is used to set or open circuit the system back to its initial stage. The system is powered with 12V power supply voltage.
The first chapter of this project is narrating on the introduction, the concept of the system and also the aims and objective. Chapter two is all about literature review. Chapter three talks about specification and operation of system component. Chapter four is operation of system. Chapter five is about construction, testing and packaging. Chapter six is conclusion, observation, recommendation and References.
1.2 AIM AND OBJECTIVE
The main aim and objective of the design and construction this project is to create a comfort in the minds of vehicle owners or users when their vehicles are parked or stationed anywhere without much fear of car-theft.
This material content is developed to serve as a GUIDE for students to conduct academic research
DOWNLOAD THIS PROJECT MATERIAL NOW!
Advertise Here
Not what you were looking for? Perform a search
What's your project topic?
Comment on Facebook:
Related Project Materials
- 1.
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER CHAPTER ONE INTRODUCTION Background of the study Transformers play a crucial r...More »
Item Type: Project Material | 54 pages | 2,013 engagements |
- 2.
THE ROLE OF ELECTRICITY TARIFF HIKES IN PROMOTING RENEWABLE ENERGY ADOPTION IN NIGERIA
CHAPTER ONE INTRODUCTION Background of the Study Renewable energy is energy derived from natural sources that are replenished at a higher rate than...More »
Item Type: Project Material | 54 pages | 1,519 engagements |
- 3.
AN ASSESMENT OF THE NATIONAL GRID FAILURES AND THE WAY FORWARD
CHAPTER ONE INTRODUCTION 1.1 Background of the study Electricity has become an essential element of contemporary life worldwide, serving various purpo...More »
Item Type: Project Material | 54 pages | 1,691 engagements |
- 4.
IMPACT OF FORMAL EDUCATION ON COMMUNITY DEVELOPMENT IN OREDO LOCAL GOVERNMENT, EDO STATE
ABSTRACT The broad objective of this study is to examine the impact of formal education on community development in Oredo Local Government, Edo State....More »
Item Type: Project Material | 54 pages | 7,224 engagements |
- 5.
CONSTRUCTION OF CRITICAL TEMPERATURE ALARM SYSTEM
ABSTRACT The term “critical point” is sometimes used to denote specifically the vapour liquid critical point of a material. The vapour liquid ...More »
Item Type: Project Material | 46 pages | 13,222 engagements |
- 6.
THE CONSTRUCTION OF LABORATORY EQUIPMENT FOR THE DETERMINATION / INVESTIGATION OF ELECTRICAL INSULAT...
ABSTRACT Insulation deterioration occurs on power system when insulators are subjected to abnormal stresses. Since insulators cannot resist indefinite...More »
Item Type: Project Material | 31 pages | 9,086 engagements |