DESIGN AND CONSTRUCTION OF AN AUTOMATIC BATTERY CHARGER ABC
Sold By: Joe Project Store | Item Type: Project Material | Report this? | Attributes: 65 pages | 1-5 chapters | Amount: ₦5,000 | 7 orders. | Marked useful: 7,491 times
INSTANT PROJECT MATERIAL DOWNLOADABSTRACT
The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure developed cover the construction of battery charger for battery sizes ranging from 6 volts to 12 volts.
The phototype of a battery charger for these ranges of battery has been implemented following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory.
Adequate care has been taken in the design and construction to ensure that the resultant battery charger is both reliable and easy to use.
CHAPTER ONE
INTRODUCTION
A battery charge is an electrical device employed in charging batteries. The batteries that are usually charged by battery chargers are the storage batteries also known as “accumulators”.
The charger is made up of various Electrical and Electronic component, which for the purpose of clarity are grouped with four basic unit;
They are;
The power supply unit
The smoothing circuit
The regulatory unit and
The regulated D.C charging unit
Battery chargers comes in various designs and voltage. The choice of a particular kind of charger that depends largely on the size of battery or batteries which one intends to charge. The miniature battery charger could be needed to charge batteries whose voltage ranges from 6-12 volts. The bigger battery chargers are for batteries with voltage ranging 12 – 48 volts. These are the heavy duty batteries.
The battery charger is built in such a way that it delivers a constant value of d.c current into the battery it is charging is the opposite direction from which current flows on the batteries during discharge. One cannot successfully design a battery charger without fundamental understanding of the accumulator because it also makes up the operation. Thus chapter two aimed at a brief study of the accumulator (accumulator). Chapter three deals with the power supply unit, which senses as the backbone of the battery charger and how the automated cut off is achieved. Chapter four full analysis’s the operation of a battery charger and its casing while chapter five which happen to be the last chapter aimed at concluding and summarizing what has been achieved at the and of the project.
This material content is developed to serve as a GUIDE for students to conduct academic research
DOWNLOAD THIS PROJECT MATERIAL NOW!
Advertise Here
Not what you were looking for? Perform a search
What's your project topic?
Comment on Facebook:
Related Project Materials
- 1.
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER CHAPTER ONE INTRODUCTION Background of the study Transformers play a crucial r...More »
Item Type: Project Material | 54 pages | 2,013 engagements |
- 2.
THE ROLE OF ELECTRICITY TARIFF HIKES IN PROMOTING RENEWABLE ENERGY ADOPTION IN NIGERIA
CHAPTER ONE INTRODUCTION Background of the Study Renewable energy is energy derived from natural sources that are replenished at a higher rate than...More »
Item Type: Project Material | 54 pages | 1,519 engagements |
- 3.
AN ASSESMENT OF THE NATIONAL GRID FAILURES AND THE WAY FORWARD
CHAPTER ONE INTRODUCTION 1.1 Background of the study Electricity has become an essential element of contemporary life worldwide, serving various purpo...More »
Item Type: Project Material | 54 pages | 1,691 engagements |
- 4.
IMPACT OF FORMAL EDUCATION ON COMMUNITY DEVELOPMENT IN OREDO LOCAL GOVERNMENT, EDO STATE
ABSTRACT The broad objective of this study is to examine the impact of formal education on community development in Oredo Local Government, Edo State....More »
Item Type: Project Material | 54 pages | 7,224 engagements |
- 5.
CONSTRUCTION OF CRITICAL TEMPERATURE ALARM SYSTEM
ABSTRACT The term “critical point” is sometimes used to denote specifically the vapour liquid critical point of a material. The vapour liquid ...More »
Item Type: Project Material | 46 pages | 13,222 engagements |
- 6.
THE CONSTRUCTION OF LABORATORY EQUIPMENT FOR THE DETERMINATION / INVESTIGATION OF ELECTRICAL INSULAT...
ABSTRACT Insulation deterioration occurs on power system when insulators are subjected to abnormal stresses. Since insulators cannot resist indefinite...More »
Item Type: Project Material | 31 pages | 9,086 engagements |